climb rate中文是什么意思

发音:

用"climb rate"造句"climb rate"怎么读"climb rate" in a sentence

中文翻译手机版

爬升率

"climb"中文翻译 vi. 1.攀登，爬上；(太阳等)徐徐上升；(飞机)爬高 ...
"rate"中文翻译 vt.,vi. 〔方言〕＝ret.
"rate climb" 中文翻译 : 等速上升; 上升率不变的上升
"rate of climb" 中文翻译 : 爬升率; 上升率; 上升速度
"rate-of-climb" 中文翻译 : 爬升率
"cabin rate of climb" 中文翻译 : 座舱升降率
"cabin rate-of-climb indicator" 中文翻译 : 座舱高度变化率指示器
"combat rate of climb" 中文翻译 : 战斗上升率
"constant-rate climb" 中文翻译 : 上升率不变的上升
"four-engined rate of climb" 中文翻译 : 用四台发动机上升时的上升率
"initial climb rate" 中文翻译 : 起始上升率
"initial rate of climb" 中文翻译 : 起始爬升率
"maximum climb rate" 中文翻译 : 最大上升率
"maximum rate of climb" 中文翻译 : 最大上升率
"negative rate of climb" 中文翻译 : 负上升率
"positive rate of climb" 中文翻译 : 上升率
"pressure rate of climb" 中文翻译 : 气压上升率
"rate-of-climb characteristics" 中文翻译 : 上升率特性
"rate-of-climb control" 中文翻译 : 上升率控制
"rate-of-climb indicator" 中文翻译 : 爬升率指示器; 爬升速率指示器; 上升率指示器
"rate-of-climb lag" 中文翻译 : 升降速度表指示滞后
"rate-of-climb meter" 中文翻译 : 爬升速度表; 升降速度表
"rate-of-climb sensor" 中文翻译 : 上升率传感器
"rate-of-climb signal" 中文翻译 : 上升率信号
"sea-level rate of climb" 中文翻译 : 海平面上升率

例句与用法

In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out , the voltage waveform harmonious which the frequency changer outputs is big , attacks in a big way , and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage , the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low , rate frequency in 8 - 20hz ; the velocity modulation scope is wide , the lowest movement frequency lowers to 1hz , and the starting number of times is quite frequently , each hour reaches as high as 600 - 800 time , the impact shoulders in a big way , the overload capacity request is high
针对这一情况本文对冶金辅传用变频辊道电机的设计进行了系统研究。首先对变频器和变频辊道电机的运行特性进行详细分析,变频器输出的电压波形谐波大,冲击大,电压上升率高达6600v / s ,是普通正弦交流电压的20倍;轧机辅传辊道对电机提出了十分严格的要求:其运行频率很低,额定频率在8 - 20hz ;调速范围宽,最低运行频率低到0 . 5hz ,起动次数相当频繁,每小时高达600 - 800次,冲击负荷大,过载能力要求较高。